Bathroom flooring
Bathroom floors chosen for how wet the room really gets, laid on a flat, stable base, and finished with a clean transition to the rooms next door.
Open daily 7 AM to 10 PM. Talk to us about your bathroom.
A powder room, a kids' bath and a primary bath with a doorless shower are three different environments. The right floor for one is the wrong floor for another.
| Material | Water tolerance | Underfoot | Good fit for |
|---|---|---|---|
| Porcelain tile | Excellent; dense and low-absorption | Hard and cool unless heated | Any bathroom, including curbless showers |
| Natural stone | Good when sealed; some stones stain or etch | Hard; honed finishes grip better | Primary baths where the look is worth the upkeep |
| Rigid-core vinyl (SPC/LVP) | Core resists water; seams and edges don't | Warmer and softer than tile | Powder rooms and light-use hall baths |
| Sheet vinyl | Good; few seams | Soft and warm | Budget-conscious secondary baths |
For a longer comparison written around Texas homes, see our guide to the best bathroom flooring for Texas houses.
Rigid-core vinyl plank is popular for good reasons. It's quick to install, warmer than tile and handles a splash. It's also floating, which means it isn't bonded to the floor underneath, and that's where bathrooms test it.
If you choose it, sealing the perimeter with a flexible sealant and keeping it out of the wet zone makes a real difference.
Most Dallas-area homes built in recent decades are on a concrete slab. We remove old flooring and adhesive, grind high spots, fill low areas with a self-leveling underlayment, and add a crack-isolation membrane before tile. Existing slab cracks are noted and bridged, not ignored.
Upper-floor baths and older pier-and-beam homes have wood framing. Tile needs a stiff floor, so we check for bounce, replace water-damaged sheathing near the toilet and tub, and add an underlayment or uncoupling membrane.
Electric mats or cables sit in the thin-set layer under tile or stone. They need a dedicated circuit and a thermostat with floor sensor, and they're tested before and after tile goes down so a damaged wire gets caught while it's still reachable.
Planning a bathroom project? Call and tell us what you have in mind. We'll talk through scope and arrange a visit. Open daily 7 AM to 10 PM.
Door to hallway
Where the bathroom floor meets the hallway or bedroom is the joint everyone steps on. It's also where height differences show up once the new floor is in.
Tile over a membrane and a heating mat can end up noticeably taller than the carpet or wood next to it. We plan the finished height of each layer so the transition is a gentle ramp rather than a trip hazard.
A low metal profile, a stone threshold or a flush joint each suits a different pairing. Wood floors outside the door also need their own expansion gap, which the profile has to cover.
Door bottoms may need trimming, and the toilet flange needs to finish flush with or just above the new floor so the seal works.
We check the floor type, flatness, existing cracks and the heights at every doorway.
Material, pattern, grout color and transition details are chosen, plus a heated-floor plan if you want one.
Toilet and sometimes the vanity come out so the floor runs underneath instead of around them.
Leveling, crack isolation, heating mat and electrical rough-in.
Floor laid and grouted, transitions installed, toilet and vanity reset with new seals and supply lines.
Cracks that run in a line across several tiles usually follow a crack in the slab below, left without an isolation membrane. A soft spot or a rocking tile in front of the toilet points to a slow leak at the wax ring and rotted subfloor. Vinyl plank that has peaked or separated at the seams usually got wet underneath, or was pinned down by the vanity with no room to move. Each fix starts by finding the cause, not just replacing the visible pieces.
Our cost page explains how we price from a measured scope.
We lay bathroom floors across Dallas and nearby cities including Richardson and Irving, and in smaller rooms as part of our hall bath and powder room remodels. Detailed tile work is covered on the tile installation page. See the complete service area list.
In a powder room or a hall bath where the floor gets splashed rather than soaked, a rigid-core (SPC) vinyl plank can work well. The core resists water, but the seams and the edges at walls and the toilet are where water gets underneath. We don't recommend it inside a shower or in a bathroom that regularly floods the floor.
Yes. Electric heating mats or cables are laid over the slab, usually with a thin insulating layer beneath them so heat goes up rather than into the concrete. They need a dedicated circuit from the electrical panel and a thermostat, which your electrician will plan for.
It can if the new floor is thicker than the old one. We measure the finished height of the new assembly, including any heating mat and membrane, and trim the door or adjust the threshold as part of the job.
Polished stone can be slick when wet. Honed, tumbled or textured finishes give much better grip, and smaller tiles with more grout lines add traction. For a bathroom floor, we steer most people toward a honed finish.
Talk to a remodeler
One call is enough to tell us what you'd like to change. We'll ask a few questions, then arrange a visit to measure and give you a written scope and estimate.
(469) 249-8764Open daily, 7:00 AM to 10:00 PM
Tap to call now